Firearms Owners Against Crime

Institute for Legal, Legislative and Educational Action

Setback: Why It's Important to Cycle Your Concealed Carry Rounds :: 02/29/2016

Not too long ago, we did an article discussing rotating the rounds that go into your everyday carry gun’s chamber. What we didn’t expect was how prevalent a concern this was in the concealed carry gun community. In this article, we’re going to talk in a little more detail on what happens to the round that gets chambered in your concealed carry gun — and a little more on how you might go about rotating it . . .

loading-a-round-into-the-chamber-720x360

Ease Up On The Upper Receiver

Everyone likes that “clink-clunk” noise the slide makes when it slams down on a round. That said, the lighter you set down the upper receiver onto the round in the magazine, the lighter the impact on the cartridge casing. If you’re at the range and planning on expending that ammo, there’s very little to worry about. Modern munitions and most handguns are designed to accomodate those tolerances. The biggest obstacle we run into is the repeated impact of the upper receiver onto the same bullet casing multiple times.

One or twice? No problem. You can potentially keep the same round chambered in your handgun for several months (or longer) depending upon how gently you chamber that round.

Here’s the ugly part: every time a bullet gets loaded into the chamber of a handgun, it’s going to take the force of the slide hitting it.  Every handgun is going to be slightly different in terms of the force it exerts on the bullet itself. There’s no all-inclusive set of rules governing when a round should be cycled out. So, we’re going to have to use common sense on this one.

Weekly Assessment 

Concealed carriers tend to use specialized self-defense rounds. These are bullets designed to expand when they hit soft tissue and, thus, have a greater impact on potential bad guys in a self-defense situation. These rounds are usually quite a bit more expensive than standard full metal jacket bullets so gunowners are understandably more hesitant to “throw away” (shoot at the range) an expensive self-defense round.

When we unload our carry guns — either to clean the, or before a range session — we have a tendency to eject the round and then put it right back in at the top of the magazine. It’s expedient and convenient. Before you throw that round right back at the top of the magazine, take an honest look at it.

Three Things To Look

The back of the casing is pretty resistant to impact but, after awhile, you could see dents start to form on the back of the casing. You may also notice dents along the side of the case. These are especially important to note. Dings, cuts, carves, and dents are all signs that a round needs to be cycled out.

Inspect the following points on the round:

  • Back of the bullet case
  • Sides of the bullet (full 360° turn)
  • Indents or scrapes on the primer

Once the round starts showing signs of wear and tear, don’t wait — cycle it out. If you’re at home or some place convenient, cycle the rounds out of the magazine and then put the “most frequently chambered” round in first.  Stack the rest on top.

Ideally, take the round out of circulation altogether.  Throw it in a safe container where you keep rounds you intend to shoot at the range.

If it’s heavily degraded or bent, decommission it.  If you’ve never had to decommission a bullet, talk to the guy or gal at your local gun shop that handles the reloading.  He’ll know more about the proper way to fully decommission a bullet that’s been severely damaged.  This doesn’t happen too often.

In conclusion, as annoying as it may be to ditch an expensive self-defense round, it’s far better to stay safe.  The biggest threat isn’t the round going off on its own, it’s usually a failure to fire or failure to eject.  None of the above are ideal for a concealed carrier using his or her handgun in self-defense.

http://www.thetruthaboutguns.com/2016/02/daniel-zimmerman/390655/

Firearms Owners Against Crime ILLEA © 2024

P.O. Box 308 Morgan, PA 15064

web application / database development by davidcdalton.com